Tu sei qui

TC-W100A Saldatrice per termocoppie (precedentemente conosciuto come TCW)

La saldatrice a termocoppia MIYACHI TC-W100A salda tra loro i fili di termocoppie per formare una giunzione a goccia uniforme, con dimensione e una qualità costanti, senza dannosi strati assodati. La TC-W100A produce termocoppie da tutte le leghe disponibili in commercio.

 

Specifiche TC-W100A Saldatrice per termocoppie

  • Camera di saldatura a gas argon
  • Facile da usare
  • Progettata per operare in produzione o laboratorio
  • Blocco innesco saldatura
  • Regolatore tensione di linea
  • Sezione dei fili da 38 AWG a 20 AWG
Quality control features .
Camera di saldatura Argon gas flowing through the weld chamber ensures a reliable, oxide-free weld.
Circuito attivazione Prestripped wire must be properly loaded into the handpiece and the handpiece correctly inserted into the weld chamber to initiate firing. This loading sequence ensures that the handpiece is double earth grounded for maximum operator safety. Internal filt
Blocco attivazione saldatura Prevents poor welds caused by attempting a weld before the capacitors recharge. This condition exists immediately after a weld has been made or the control has been reset.
Regolatore tensione di linea Maintains the capacitor bank voltage within ±0.25% of setting for a ±13% change in line voltage. This feature ensures consistent thermocouple weld quality.
Flessione guasto di linea Welder automatically activates the turndown circuit, discharging the capacitor bank when the line voltage is interrupted. This circuit ensures consistent welds and protects the operator from inadvertent discharge
Controlli
Interruttore di accensione Disconnects both sides of the input power line when switched to the “OFF” position.
Pronto per saldatura Indicates that the capacitor bank has fully recharged and is ready to make a weld.
Selezione sezione filo Controls the level of stored energy necessary to make a thermocouple weld. Energy levels are indicated for each American Wire Gauge (AWG) from 38 AWG to 20 AWG. Because of variations in he melting characteristics of thermocouple alloys, it may be necessar
Specifiche
Circuito a stato solido Components conservatively rated when used within the maximum specified repetition rates. The charging circuit uses thyristors in a unique manner to provide high reliability and precise charging intervals.
Correnti e tensioni operative 115 V/0.5 A, 230 V/0.3 A, or 100 V/0.5 A at 50/60 Hz
Potenza di standby Approximately 15 watts
Energia immagazzinata nominale Range 3 to 190 watt-seconds (joules)
Banco condensatore 18,300 MFD ±10% at 20° C. Three capacitors are grouped in a single bank. At full rating, the capacitor bank is operated at 144 volts.
Velocità di saldatura As a manual feed thermocouple welder, the maximum number of welds per minute is determined by how fast the handpiece can be loaded and inserted into the weld chamber. The actual weld time is less than .1 seconds, and the time for the circuitry to recharge
Flusso gas Argon Recommended flow rate is 3 cubic feet per hour.
Interruzione gas Argon Blocks the flow of argon gas to the weld chamber when line voltage is turned off.
Morsetti (venduti a parte) TCWCS38 clamp for 32 to 38 gauge wire TCWCS31 clamp for 27 to 31 gauge wire TCWCS26 clamp for 23 to 26 gauge wire TCWCS22 clamp for 20 to 22 gauge wire
MASSA E DIMENSIONI
Powersupply Dimensions (LxWxH) 25.4 cm x 26.0 cm x 17.5 cm (10 in x 10.25 in x 6.875 in)
Powersupply Weight 7.3 kg (16.2 lb ) (includes handpiece)
Handpiece Dimensions (LxWxH) Body Length: 10.16 cm (4 in) Body Diameter: 1.91 cm (0.75 in)
Handpiece Weight 7.3 kg (16.2 lb ) (includes handpiece)
Wire clamp Dimensions (LxWxH) Length: 1.91 cm (0.75 in) Diameter: 0.64 cm (0.25 in)
Wire clamp Weight 91 gm (0.2 lb)

Soluzioni personalizzate

Inviate un campione a uno dei nostri centri tecnologici in Europa per una valutazione. Valuteremo la soluzione che soddisfa meglio le vostre esigenze. AMADA WELD TECH conduce test di fattibilità e eroga consulenza applicativa.

Contatti